Citrix SD-WAN

SNMP

May 5, 2021

Contributed by:

S C

Citrix SD-WAN supports SNMPV1/V2 capability and only a single user account for each SNMPv3 capability. This restriction provides the following advantages:

Ensuring SNMPv3 compliance for network devices
Verification of SNMPv3 capability
Easy configuration of SNMPv3

To configure SNMPv3 Polling and Traps, navigate to the SNMPv3 section of the Configuration -> Appliance Settings -> SNMP page, and fill in the fields as required.

NOTE

To configure an IPv6 address, ensure that the SNMP server is also configured with an IPv6 address.

SNMP settings

Standard MIB Support

The following standard MIBs are supported by the SD-WAN Appliances.

MIB	RFC (Definition Link)
DISMAN-EVENT-MIB	https://www.ietf.org/rfc/rfc2981.txt
IF-MIB	https://www.ietf.org/rfc/rfc2863.txt
IP-FORWARD-MIB	https://www.ietf.org/rfc/rfc4292.txt
IP-MIB (Partial)	https://www.ietf.org/rfc/rfc4293.txt
Q-BRIDGE-MIB (Partial)	http://www.ieee802.org/1/files/public/MIBs/IEEE8021-Q-BRIDGE-MIB-201112120000Z.mib
RFC1213-MIB	https://www.ietf.org/rfc/rfc1213.txt
SNMPv2-MIB	https://www.ietf.org/rfc/rfc3418.txt
TCP-MIB	https://www.ietf.org/rfc/rfc4022.txt
P-BRIDGE-MIB.txt	http://www.icir.org/fenner/mibs/extracted/P-BRIDGE-MIB-rfc2674.txt
RMON2-MIB.txt	https://www.ietf.org/rfc/rfc3273.txt
TOKEN-RING-RMON-MIB.txt	http://www.icir.org/fenner/mibs/extracted/TOKEN-RING-RMON-MIB-rmonmib-01.txt

You must download the following SNMP files before you can start monitoring a Citrix SD-WAN appliance:

CITRIX-COMMON-MIB.txt
APPACCELERATION-SMI.txt
APPACCELERATION-PRODUCTS-MIB.txt
APPACCELERATION-TC.txt
APPACCELERATION-STATUS-MIB.txt
APPCACHE-MIB.txt
SDX-MIB-smiv2.mib

The MIB files are used by SNMPv3 managers and SNMPv3 trap listeners. The files include the SD-WAN appliance enterprise MIBs, which provide SD-WAN-specific events. To download MIB files, in the SD-WAN web management interface:

Navigate to Configuration > Appliance Settings > SNMP > Download MIB File page.
Select the required MIB file.
Click View.

The MIB file opens in MIB browser.
Note
- Support for these MIBs is provided by default by the net-snmp snmpd daemon process on Linux systems. The MIBs provide the basis for supporting Network Management applications.
- The Ethernet port packet and byte counters are in the IF-MIB inside the ifTable. System information is in the system object.
- Ethernet ports are included in the ifTable, so walking that must be sufficient to ensure that the SNMP subsystem is running.
- Support for the Q-BRIDGE-MIB and the IP-MIB provides support for the network mapping application.
For additional information about adding SNMP manager, configuring SNMP View/Alarm, and adding SNMP server, see the CloudBridge 7.4 documentation at: CloudBridge

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

SNMP

May 5, 2021

Contributed by:

S C

May 5, 2021

Contributed by:

S C

SNMP

Standard MIB Support

In this article