ADC

Configuring a Rewrite Policy

August 20, 2024

Contributed by:

C C S

After you create any needed rewrite action(s), you must create at least one rewrite policy to select the requests that you want the Citrix ADC appliance to rewrite.

A rewrite policy consists of a rule, which itself consists of one or more expressions, and an associated action that is performed if a request or response matches the rule. Policy rules for evaluating HTTP requests and responses can be based on almost any part of a request or response.

Even though you cannot use TCP rewrite actions to rewrite data other than the TCP payload, you can base the policy rules for TCP rewrite policies on the information in the transport layer and the layers below the transport layer.

If a configured rule matches a request or response, the corresponding policy is triggered and the action associated with it is carried out.

Note: You can use either the command line interface or the configuration utility to create and configure rewrite policies. Users who are not thoroughly familiar with the command line interface and the Citrix ADC Policy expression language will usually find using the configuration utility much easier.

To add a new rewrite policy by using the command line interface

At the command prompt, type the following commands to add a new rewrite policy and verify the configuration:

<add rewrite policy <name> <expression> <action> [<undefaction>]
<show rewrite policy <name>

Example 1. Rewriting HTTP Content:

> add rewrite policy policyNew "HTTP.RES.IS_VALID" insertact NOREWRITE
 Done
> show rewrite policy policyNew
        Name: policyNew
        Rule: HTTP.RES.IS_VALID
        RewriteAction: insertact
        UndefAction: NOREWRITE
        Hits: 0
        Undef Hits: 0

 Done
<!--NeedCopy-->

Example 2. Rewriting a TCP Payload (TCP Rewrite):

> add rewrite policy client_tcp_payload_policy CLIENT.IP.SRC.EQ(172.168.12.232) client_tcp_payload_replace_all
 Done
> show rewrite policy client_tcp_payload_policy
        Name: client_tcp_payload_policy
        Rule: CLIENT.IP.SRC.EQ(172.168.12.232)
        RewriteAction: client_tcp_payload_replace_all
        UndefAction: Use Global
        LogAction: Use Global
        Hits: 0
        Undef Hits: 0

 Done
>
<!--NeedCopy-->

To modify an existing rewrite policy by using the command line interface

At the command prompt, type the following commands to modify an existing rewrite policy and verify the configuration:

<set rewrite policy <name> -rule <expression> -action <action> [<undefaction>]
<show rewrite policy <name>

Example:

> set rewrite policy policyNew -rule "HTTP.RES.IS_VALID" -action insertaction
 Done

> show rewrite policy policyNew
        Name: policyNew
        Rule: HTTP.RES.IS_VALID
        RewriteAction: insertaction
        UndefAction: NOREWRITE
        Hits: 0
        Undef Hits: 0

 Done
<!--NeedCopy-->

To remove a rewrite policy by using the command line interface

At the command prompt, type the following command to remove a rewrite policy:

rm rewrite policy <name>

Example:

> rm rewrite policy policyNew
Done
<!--NeedCopy-->

To configure a rewrite policy by using the configuration utility

<Navigate to AppExpert > Rewrite > Policies.
<In the details pane, do one of the following:
- <To create a new policy, click Add.
- <To modify an existing policy, select the policy, and then click Open.
<Click Create or OK. A message appears in the status bar, stating that the Policy has been configured successfully.
<Repeat steps 2 through 4 to create or modify as many rewrite actions as you wish.
<Click Close. To delete a rewrite policy, select the rewrite policy you want to delete, then click Remove and, when prompted, confirm your choice by clicking OK.

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

Configuring a Rewrite Policy

August 20, 2024

Contributed by:

C C S

August 20, 2024

Contributed by:

C C S

Configuring a Rewrite Policy

To add a new rewrite policy by using the command line interface

To modify an existing rewrite policy by using the command line interface

To remove a rewrite policy by using the command line interface

To configure a rewrite policy by using the configuration utility

In this article