ADC

Common switch for client, server, and backplane

August 20, 2024

Contributed by:

C C S

In this deployment, the client, server, and backplane use dedicated interfaces on the same switch to communicate with the Citrix ADC cluster.

localize image

NS0 - nodeId: 0, NSIP: 10.102.29.60
NS1 - nodeId: 1, NSIP: 10.102.29.70
NS2 - nodeId: 2, NSIP: 10.102.29.80

To deploy a cluster with a common switch for the client, server, and backplane
1. Create a cluster of nodes NS0, NS1, and NS2.
2. Log on to the first node that you want to add to the cluster and do the following:
```
> create cluster instance 1
> add cluster node 0 10.102.29.60 -state ACTIVE -backplane 0/1/1
> enable cluster instance 1
> add ns ip 10.102.29.61 255.255.255.255 -type CLIP
> save ns config
> reboot -warm
```
3. Log on to the cluster IP address and do the following:
```
> add cluster node 1 10.102.29.70 -state ACTIVE -backplane 1/1/1
> add cluster node 2 10.102.29.80 -state ACTIVE -backplane 2/1/1
```
4. Log on to the nodes 10.102.29.70 and 10.102.29.80 to join the nodes to the cluster.
```
> join cluster -clip 10.102.29.61 -password nsroot
> save ns config
> reboot -warm
```
As seen in the above commands the interfaces 0/1/1, 1/1/1, and 2/1/1 are configured as the backplane interfaces of the three cluster nodes.

On the cluster IP address, create VLANs for the backplane, client, and server interfaces.

//For the backplane interfaces
```
> add vlan 10
> bind vlan 10 0/1/1 1/1/1 2/1/1
```
//For the client-side interfaces
```
> add vlan 20
> bind vlan 20 0/1/2 1/1/2 2/1/2
```
//For the server-side interfaces
```
> add vlan 30
> bind vlan 30 0/1/3 1/1/3 2/1/3
```
On the switch, create VLANs for the interfaces corresponding to the backplane interfaces and the client and server interfaces. The following sample configurations are provided for the Cisco® Nexus 7000 C7010 Release 5.2(1) switch. Similar configurations must be performed on other switches.</span>

//For the backplane interfaces. Repeat for each interface…
```
> interface Ethernet2/47
  switchport access vlan 100
  switchport mode access
  end
```
//For the client interfaces. Repeat for each interface…
```
> interface Ethernet2/48
  switchport access vlan 200
  switchport mode access
  end
```
//For the server interfaces. Repeat for each interface…
```
> interface Ethernet2/49
  switchport access vlan 300
  switchport mode access
  end
```

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

Common switch for client, server, and backplane

August 20, 2024

Contributed by:

C C S

August 20, 2024

Contributed by:

C C S

Common switch for client, server, and backplane

In this article