This content has been machine translated dynamically.
Dieser Inhalt ist eine maschinelle Übersetzung, die dynamisch erstellt wurde. (Haftungsausschluss)
Cet article a été traduit automatiquement de manière dynamique. (Clause de non responsabilité)
Este artículo lo ha traducido una máquina de forma dinámica. (Aviso legal)
此内容已经过机器动态翻译。 放弃
このコンテンツは動的に機械翻訳されています。免責事項
이 콘텐츠는 동적으로 기계 번역되었습니다. 책임 부인
Este texto foi traduzido automaticamente. (Aviso legal)
Questo contenuto è stato tradotto dinamicamente con traduzione automatica.(Esclusione di responsabilità))
This article has been machine translated.
Dieser Artikel wurde maschinell übersetzt. (Haftungsausschluss)
Ce article a été traduit automatiquement. (Clause de non responsabilité)
Este artículo ha sido traducido automáticamente. (Aviso legal)
この記事は機械翻訳されています.免責事項
이 기사는 기계 번역되었습니다.책임 부인
Este artigo foi traduzido automaticamente.(Aviso legal)
这篇文章已经过机器翻译.放弃
Questo articolo è stato tradotto automaticamente.(Esclusione di responsabilità))
Translation failed!
Dynamic cluster link aggregation
Dynamic cluster LA channel uses Link Aggregation Control Protocol (LACP).
You must perform similar configurations on the cluster IP address and on the external connecting device. If possible, configure the upstream switch to distribute traffic based on IP address or port instead of MAC address.
Points to remember:
-
Enable LACP (by specifying the LACP mode as either ACTIVE or PASSIVE).
Note
Make sure the LACP mode is not set as PASSIVE on both the Citrix ADC cluster and the external connecting device.
-
Specify the same LACP key on each interface that you want to be the part of the channel. For creating a cluster LA channel, the LACP key can have a value from 5 through 8. For example, if you set the LACP key on interfaces 0/1/2, 1/1/2, and 2/1/2 to 5, CLA/1 is created. The interfaces 0/1/2, 1/1/2, and 2/1/2 are automatically bound to CLA/1. Similarly, if you set the LACP key to 6, CLA/2 channel is created.
-
Specify the LAG type as Cluster.
To configure a dynamic cluster LA channel by using the command line interface
On the cluster IP address, for each interface that you want to add to the cluster LA channel, type:
set interface <id> -lacpMode <lacpMode> -lacpKey <positive_integer> -lagType CLUSTER<!--NeedCopy-->
Example:
To configure a cluster LA channel CLA/1 of 3 interfaces.
> set interface 0/1/2 -lacpMode active -lacpKey 5 -lagType Cluster
> set interface 1/1/2 -lacpMode active -lacpKey 5 -lagType Cluster
> set interface 2/1/2 -lacpMode active -lacpKey 5 -lagType Cluster
Note
Optionally, you can enable Link Redundancy in a Cluster with LACP.
Similarly, configure dynamic LA on the external switch. The following sample configurations are provided for the Cisco® Nexus 7000 C7010 Release 5.2(1). Similar configurations must be performed on other switches.
Global config:
Configure terminal
feature lacp
Interface level config:
interface Ethernet2/47
switchport
switchport access vlan 10
channel-group 7 mode active
no shutdown
interface Ethernet2/48
switchport
switchport access vlan 10
channel-group 7 mode active
no shutdown
Share
Share
This Preview product documentation is Cloud Software Group Confidential.
You agree to hold this documentation confidential pursuant to the terms of your Cloud Software Group Beta/Tech Preview Agreement.
The development, release and timing of any features or functionality described in the Preview documentation remains at our sole discretion and are subject to change without notice or consultation.
The documentation is for informational purposes only and is not a commitment, promise or legal obligation to deliver any material, code or functionality and should not be relied upon in making Cloud Software Group product purchase decisions.
If you do not agree, select I DO NOT AGREE to exit.