Gateway

Optimizing Citrix Gateway VPN split tunnel for Office365

January 8, 2024

Contributed by:

As organizations are adapting to the remote work options more rapidly than before, the remote access infrastructure must be optimized to facilitate seamless connectivity during increased traffic load conditions.

Microsoft recommends excluding traffic destined to key Office 365 services from the scope of VPN connection by configuring split tunneling using published IPv4 and IPv6 address ranges. For best performance and most efficient use of VPN capacity, traffic to this dedicated IP address ranges associated with Office 365 Exchange Online, SharePoint Online and Microsoft Teams (referred to as Optimize category in Microsoft documentation) should be routed directly, outside of the VPN tunnel. Refer to [Microsoft guidance] https://docs.microsoft.com/en-us/Office365/Enterprise/office-365-vpn-split-tunnel for more detailed information about this recommendation.

Microsoft’s recommendation in Citrix Gateway is achieved by routing the Microsoft provided list of IP addresses directly to the internet for the O365 traffic by using the split tunnel reverse configuration.

The configuration involves the following that can be performed manually by using the GUI or CLI commands.

Configure split tunnel for reverse configuration
Configure intranet applications for user access to resources

Configuration by using the GUI

To configure split tunneling by using the GUI

On the Configuration tab, Navigate to Citrix Gateway > Global Settings.
In the details pane, under Settings, click Change Global Settings.
On the Client Experience tab, in Split Tunnel, select Reverse.
Click OK.

To create VPN intranet application by using the GUI

On the Configuration tab, Navigate to Citrix Gateway > Global Settings.
In the details pane, under Intranet Applications, click the link.
In the Configure VPN Intranet Application page, click Add, and then click New.
In Name, type a name for the profile.
In Protocol, select the protocol that applies to the network resource.
In Destination Type, select IP Address and Netmask.
In IP Address, enter the IP address that must be routed directly to the internet for O365 traffic. For the list of IP address, see List of IP addresses.
In Netmask, enter the netmask IP address.
Click Create and then click Close.

Note: Repeat this procedure for all the IP addresses.

Configuration by using the CLI

To set split tunnel to reverse, at the command prompt, type;

set vpn parameter -splitTunnel REVERSE
<!--NeedCopy-->

To add VPN intranet application, at the command prompt, type;

add vpn intranetApplication intranetapp1 ANY 13.107.6.152 -netmask 255.255.255.254 -destPort 1-65535 -interception TRANSPARENT
<!--NeedCopy-->

Note: Repeat this procedure for all the IP addresses.

To bind the intranet application, at the command prompt type;

bind vpn global -intranetApplication intranetapp1
<!--NeedCopy-->

List of IP addresses of Office 365 services (EXO, SPO, and Teams)

Reference: https://docs.microsoft.com/en-us/office365/enterprise/urls-and-ip-address-ranges

Note from Microsoft: As part of Microsoft’s response to the COVID-19 situation, Microsoft has declared a temporary moratorium on some planned URL and IP address changes. This moratorium is intended to provide customer IT teams with confidence and simplicity in implementing recommended network optimizations for work-from-home Office 365 scenarios. From March 24, 2020 through June 30, 2020 this moratorium will halt changes for key Office 365 services (Exchange Online, SharePoint Online, and Microsoft Teams) to IP ranges and URLs included in the Optimize category.

IPv4 address range

104.146.128.0/17
13.107.128.0/22
13.107.136.0/22
13.107.18.10/31
13.107.6.152/31
13.107.64.0/18
131.253.33.215/32
132.245.0.0/16
150.171.32.0/22
150.171.40.0/22
191.234.140.0/22
204.79.197.215/32
23.103.160.0/20
40.104.0.0/15
40.108.128.0/17
40.96.0.0/13
52.104.0.0/14
52.112.0.0/14
52.96.0.0/14
52.120.0.0/14|

IPv6 address range

2603:1006::/40
2603:1016::/36
2603:1026::/36
2603:1036::/36
2603:1046::/36
2603:1056::/36
2603:1096::/38
2603:1096:400::/40
2603:1096:600::/40
2603:1096:a00::/39
2603:1096:c00::/40
2603:10a6:200::/40
2603:10a6:400::/40
2603:10a6:600::/40
2603:10a6:800::/40
2603:10d6:200::/40
2620:1ec:4::152/128
2620:1ec:4::153/128
2620:1ec:c::10/128
2620:1ec:c::11/128
2620:1ec:d::10/128
2620:1ec:d::11/128
2620:1ec:8f0::/46
2620:1ec:900::/46
2620:1ec:a92::152/128
2620:1ec:a92::153/128
2a01:111:f400::/48
2620:1ec:8f8::/46
2620:1ec:908::/46
2a01:111:f402::/48

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

Optimizing Citrix Gateway VPN split tunnel for Office365

January 8, 2024

Contributed by:

January 8, 2024

Contributed by:

Optimizing Citrix Gateway VPN split tunnel for Office365

Configuration by using the GUI

To configure split tunneling by using the GUI

To create VPN intranet application by using the GUI

Configuration by using the CLI

List of IP addresses of Office 365 services (EXO, SPO, and Teams)

IPv4 address range

IPv6 address range

In this article