NetScaler SDX

NetScaler SDX 22040, SDX 22060, SDX 22080, SDX 22100, and SDX 22120

The NetScaler SDX 22040/22060/22080/22100/22120 are 2U appliances. Each model has two 8-core processors (32 cores with hyper-threading) and 256 GB of memory. The SDX 22040/22060/22080/22100/22120 appliances are available in two port configurations:

  • Twelve 1G SFP ports and twenty-four 10G SFP+ ports (12x1G SFP + 24x10G SFP+)
  • Twenty-four 10G SFP+ ports (24x10G SFP+)

The following figure shows the front panel of the SDX 22040/22060/22080/22100/22120 (12x1G SFP + 24x10G SFP+) appliance.

Figure 1. NetScaler SDX 22040/22060/22080/22100/22120 (12x1G SFP + 24x10G SFP+), front panel

SDX 22040 front panel

The following figure shows the front panel of the SDX 22040/22060/22080/22100/22120 (24x10G SFP+) appliance.

Figure 2. NetScaler SDX 22040/22060/22080/22100/22120 (24x10G SFP+), front panel

SDX 22040 10G front panel

Depending on the model, the appliance has the following ports:

  • RS232 serial Console Port.
  • 10/100Base-T copper Ethernet Port (RJ45), also called the LOM port. You can use this port to remotely monitor and manage the appliance independently of the NetScaler software.
  • Two 10/100/1000Base-T copper Ethernet Management Ports (RJ45), numbered 0/1 and 0/2 from left to right. These ports are used to connect directly to the appliance for system administration functions.
  • Network Ports
    • SDX 22040/22060/22080/22100/22120 (12x1G SFP + 24x10G SFP+). Twelve copper or fiber 1G SFP ports and twenty-four 10G SFP+ ports.
    • SDX 22040/22060/22080/22100/22120 (24x10G SFP+). Twenty-four 10G SFP+ ports.

The following figure shows the back panel of the SDX 22040/22060/22080/22100/22120 appliances.

Figure 3. NetScaler SDX 22040/22060/22080/22100/22120, back panel

SDX 22040 back panel

The following components are visible on the back panel of the SDX 22040/22060/22080/22100/22120 appliance:

  • Non-maskable interrupt (NMI) Button, used at the request of Technical Support to initiate a core dump. To press this red button, which is recessed to prevent unintentional activation, use a pen, pencil, or other pointed object. The NMI Button is also available remotely over the network in the LOM GUI, in the Remote Control menu.

  • System status LED, which indicates the status of the appliance, as described in LCD Display and LED Status Indicators.

    Note: On an SDX 22040/22060/22080/22100/22120 appliance running LOM firmware version 3.22, the system status LED indicates an error (continuously glows RED) even though the appliance is functioning properly.

  • Four power supplies, each rated at 750 watts, 100–240 volts. A minimum of two power supplies are required for proper operation. The extra power supplies act as backup. Each power supply has an LED that indicates the status of the power supply, as described in LCD Display and LED Status Indicators.

  • Power switch, which turns off power to the appliance. Press the switch for less than two seconds to shut off the power.

  • One 256 GB or larger removable solid-state drive.

    Note: Drive densities might increase as components become EOL but its size is never smaller than the original.

NetScaler SDX 22040, SDX 22060, SDX 22080, SDX 22100, and SDX 22120

In this article