Product Documentation
ADC
14.1 - Current Release 13.1 13.0 12.1
View PDF

Managing Client Connections

August 20, 2024
Contributed by: 
C C

To ensure efficient management of client connections, you can configure the content switching virtual servers on the Citrix ADC appliance to use the following features:

  • Configuring the ICMP Response. You can configure the Citrix ADC appliance to send ICMP responses to PING requests according to your settings. On the IP address corresponding to the virtual server, set the ICMP RESPONSE to VSVR_CNTRLD, and on the virtual server, set the ICMP VSERVER RESPONSE. The following settings can be made on a virtual server:
    • When you set ICMP VSERVER RESPONSE to PASSIVE on all virtual servers, the Citrix ADC appliance always responds.
    • When you set ICMP VSERVER RESPONSE to ACTIVE on all virtual servers, the ADC appliance responds even if one virtual server is UP.
    • When you set ICMP VSERVER RESPONSE to ACTIVE on some and PASSIVE on others, ADC appliance responds even if one virtual server set to ACTIVE is UP.

Redirecting Client Requests to a Cache

The Citrix ADC cache redirection feature redirects HTTP requests to a cache. You can significantly reduce the burden of responding to HTTP requests and improve your Web site performance through proper implementation of the cache redirection feature.

A cache stores frequently requested HTTP content. When you configure cache redirection on a virtual server, the Citrix ADC appliance sends cacheable HTTP requests to the cache and non-cacheable HTTP requests to the origin Web server. For more information on cache redirection, see “Cache Redirection.

To configure cache redirection on a virtual server by using the command line interface

At the command prompt, type:

set cs vserver <name> -cacheable <Value>

Example

set cs vserver Vserver-CS-1 -cacheable yes

To configure cache redirection on a virtual server by using the configuration utility

  1. Navigate to Traffic Management > Content Switching > Virtual Servers, and open a virtual server.
  2. In Advanced Settings, select Traffic Settings, and select Cacheable.

Enabling Delayed Cleanup of Virtual Server Connections

Under certain conditions, you can configure the down state flush setting to terminate existing connections when a service or a virtual server is marked DOWN. Terminating existing connections frees resources and in certain cases speeds recovery of overloaded load balancing setups.

To configure the down state flush setting on a virtual server by using the command line interface

At the command prompt, type:

set cs vserver <name> -downStateFlush <Value>

Example 

set cs vserver Vserver-CS-1 -downStateFlush enabled
<!--NeedCopy-->

To configure the down state flush setting on a virtual server by using the configuration utility

  1. Navigate to Traffic Management > Content Switching > Virtual Servers, and open a virtual server.
  2. In Advanced Settings, select Traffic Settings, and then select Down State Flush.

Rewriting Ports and Protocols for Redirection

Virtual servers and the services that are bound to them may use different ports. When a service responds to an HTTP connection with a redirect, you may need to configure the Citrix ADC appliance to modify the port and the protocol to ensure that the redirection goes through successfully. You do this by enabling and configuring the redirectPortRewrite setting.

To configure HTTP redirection on a virtual server by using the command line interface

At the command prompt, type:

set cs vserver <name> -redirectPortRewrite <Value>

Example 

set cs vserver Vserver-CS-1 -redirectPortRewrite enabled
<!--NeedCopy-->

To configure HTTP redirection on a virtual server by using the configuration utility

  1. Navigate to Traffic Management > Content Switching > Virtual Servers, and open a virtual server.
  2. In Advanced Settings, select Traffic Settings, and select Rewrite.

Inserting the IP Address and Port of a Virtual Server in the Request Header

If you have multiple virtual servers that communicate with different applications on the same service, you must configure the Citrix ADC appliance to add the IP address and port number of the appropriate virtual server to the HTTP requests that are sent to that service. This setting allows applications running on the service to identify the virtual server that sent the request.

If the primary virtual server is down and the backup virtual server is up, the configuration settings of the backup virtual server are added to the client requests. If you want the same header tag to be added, regardless of whether the requests are from the primary virtual server or backup virtual server, you must configure the required header tag on both virtual servers.

Note

This option is not supported for wildcarded virtual servers or dummy virtual servers.

To insert the IP address and port of the virtual server in the client requests by using the command line interface

At the command prompt, type:

set cs vserver <name> -insertVserverIPPort <vServerIPPORT>

Example 

set cs vserver Vserver-CS-1 -insertVserverIPPort 10.201.25.136:80
<!--NeedCopy-->

To insert the IP address and port of the virtual server in the client requests by using the configuration utility

  1. Navigate to Traffic Management > Content Switching > Virtual Servers, and open a virtual server.
  2. In Advanced Settings, select Traffic Settings and, in the Virtual Server IP Port Insertion list, select VIPADDR or V6TOV4MAPPING, and specify a port header in Virtual Server IP Port Insertion Value.

Setting a Time-out Value for Idle Client Connections

You can configure a virtual server to terminate any idle client connections after a configured time-out period elapses. When you configure this setting, the Citrix ADC appliance waits for the time you specify and, if the client is idle after that time, it closes the client connection.

To set a time-out value for idle client connections by using the command line interface

At the command prompt, type:

set cs vserver <name> -cltTimeout <Value>

Example 

set cs vserver Vserver-CS-1 -cltTimeout 100
<!--NeedCopy-->

To set a time-out value for idle client connections by using the configuration utility

  1. Navigate to Traffic Management > Content Switching > Virtual Servers, and open a virtual server.
  2. In Advanced Settings, select Traffic Settings, and specify a Client Idle Time-Out value.

Identifying Connections with the 4-tuple and Layer 2 Connection Parameters

You can now set the L2Conn option for a content switching virtual server. With the L2Conn option set, connections to the content switching virtual server are identified by the combination of the 4-tuple (<source IP>:<source port>::<destination IP>:<destination port>) and Layer 2 connection parameters. The Layer 2 connection parameters are the MAC address, VLAN ID, and channel ID.

To set the L2Conn option for a content switching virtual server by using the command line interface

At the command line, type the following commands to configure the L2Conn parameter for a content switching virtual server and verify the configuration:

    -  set cs vserver <name> -l2Conn (**ON** | **OFF**)
    -  show cs vserver <name>
<!--NeedCopy-->

Example 

> set cs vserver mycsvserver -l2Conn ON
Done
> show cs vserver mycsvserver
     mycsvserver (192.0.2.56:80) - HTTP   Type: CONTENT
     State: UP
         . . .
         . . .
     L2Conn: ON Case Sensitivity: ON
         . . .
         . . .
Done
>
<!--NeedCopy-->

To set the L2Conn option for a content switching virtual server by using the configuration utility

  1. Navigate to Traffic Management > Content Switching > Virtual Servers, and open a virtual server.
  2. In Advanced Settings, select Traffic Settings, and then select Layer 2 Parameters.
Managing Client Connections
August 20, 2024
Contributed by: 
C C
August 20, 2024
Contributed by: 
C C

In this article

Site feedback | Your privacy choices footer linkYour Privacy Choices | Privacy and legal terms | Cookie preferences | Consent settings | docs.cloud.com
© 1999- Cloud Software Group, Inc. All rights reserved.