Product Documentation
ADC
14.1 - Current Release 13.1 13.0 12.1
View PDF

Bind an HTTP DoS monitor and policy

August 20, 2024
Contributed by: 
C C S

To put HTTP DoS protection into effect after you have configured an HTTP DoS service, you must bind the monitor, and then bind the service to the HTTP DoS policy.

Bind the monitor to the service by using the CLI

At the command prompt, type the following commands to bind the monitor to the service and verify the configuration:

-  bind lb monitor <monitorName> <serviceName>
-  show lb monitor  
<!--NeedCopy-->

Example:

> bind lb monitor tcp ser-HTTP-DoS
 Done
> show lb monitor
1)   Name.......:   ping-default  Type......:      PING   State....ENABLED
2)   Name.......:    tcp-default  Type......:       TCP   State....ENABLED
3)   Name.......:           ping  Type......:      PING   State....ENABLED
4)   Name.......:            tcp  Type......:       TCP   State....ENABLED
5)   Name.......:           http  Type......:      HTTP   State....ENABLED
 .
 .
 .
17)   Name.......:       ldns-dns  Type......:  LDNS-DNS   State....ENABLED
 Done
<!--NeedCopy-->

Bind the policy to the service by using the CLI

At the command prompt, type the following commands to bind the policy to the service and verify the configuration:

bind service <serviceName> -policyName <policyname>

Example:

> bind service ser-HTTP-DoS -policyName pol-HTTP-DoS
 Done
> show service
1)      srv-http-10 (10.102.29.30:80) - HTTP
        State: DOWN
        Last state change was at Wed Jul  8 07:49:52 2009
        Time since last state change: 34 days, 01:24:58.510
        Server Name: 10.102.29.30
        Server ID : 0   Monitor Threshold : 0
        Max Conn: 0     Max Req: 0      Max Bandwidth: 0 kbits
        Use Source IP: NO
        Client Keepalive(CKA): NO
        Access Down Service: NO
        TCP Buffering(TCPB): NO
        HTTP Compression(CMP): NO
        Idle timeout: Client: 180 sec   Server: 360 sec
        Client IP: DISABLED
        Cacheable: NO
        SC: OFF
        SP: ON
        Down state flush: ENABLED
        .
        .
        .
4)      ser-HTTP-Dos (10.102.29.18:88) - HTTP
        State: DOWN
        Last state change was at Tue Aug 11 08:19:45 2009
        Time since last state change: 0 days, 00:55:05.40
        Server Name: 10.102.29.18
        Server ID : 0   Monitor Threshold : 0
        Max Conn: 0     Max Req: 0      Max Bandwidth: 0 kbits
        Use Source IP: NO
        Client Keepalive(CKA): NO
        Access Down Service: NO
        TCP Buffering(TCPB): NO
        HTTP Compression(CMP): YES
        Idle timeout: Client: 180 sec   Server: 360 sec
        Client IP: DISABLED
        Cacheable: NO
        SC: OFF
        SP: ON
        Down state flush: ENABLED
5)      ser-HTTP-Dos1 (10.102.29.40:87) - HTTP
        State: DOWN
        Last state change was at Tue Aug 11 08:23:40 2009
        Time since last state change: 0 days, 00:51:10.110
        Server Name: 10.102.29.40
        Server ID : 0   Monitor Threshold : 0
        Max Conn: 0     Max Req: 20     Max Bandwidth: 0 kbits
        Use Source IP: NO
        Client Keepalive(CKA): NO
        Access Down Service: NO
        TCP Buffering(TCPB): NO
        HTTP Compression(CMP): YES
        Idle timeout: Client: 180 sec   Server: 360 sec
        Client IP: DISABLED
        Cacheable: NO
        SC: OFF
        SP: OFF
        Down state flush: ENABLED
 Done
<!--NeedCopy-->

Bind the monitor and policy to the service by using the GUI

  1. Navigate to Traffic Management > Load Balancing > Services.
  2. In the details pane, select the service that you want to bind, and then click Open.
  3. In the Configure Service dialog box, select the Monitor tab, click the name of the monitor you want in the Monitors list, and then click Add. The selected monitor is added to the Configured frame.
  4. Select the Policies tab, then select the HTTP DoS tab.
  5. Select a policy from the Available Policies list, and then click Add. The policy appears in the Configured Policies list.
  6. Click OK, and then click Close. A message appears in the status bar, stating that the service has been configured.
Bind an HTTP DoS monitor and policy
August 20, 2024
Contributed by: 
C C S
August 20, 2024
Contributed by: 
C C S

In this article

Site feedback | Your privacy choices footer linkYour Privacy Choices | Privacy and legal terms | Cookie preferences | Consent settings | docs.cloud.com
© 1999- Cloud Software Group, Inc. All rights reserved.