ADC

The no-monitor option for services

August 20, 2024

Contributed by:

C C S

If you use an external system to perform health checks on the services and do not want the Citrix ADC appliance to monitor the health of a service, you can set the no-monitor option for the service. If you do so, the appliance does not send probes to check the health of the service but shows the service as UP. Even if the service goes DOWN, the appliance continues to send traffic from the client to the service as specified by the load balancing method.

The monitor can be in the ENABLED or DISABLED state when you set the no-monitor option, and when you remove the no-monitor option, the earlier state of the monitor is resumed.

You can set the no-monitor option for a service when creating the service. You can also set the no-monitor option on an existing service.

The following are the consequences of setting the no-monitor option:

If a service for which you enabled the no-monitor option goes down, the appliance continues to show the service as UP and continues to forward traffic to the service. A persistent connection to the service can worsen the situation. In that case, or if many services shown as UP are actually DOWN, the system may fail. To avoid such a situation, when the external mechanism that monitors the services reports that a service that is DOWN, remove the service from the Citrix ADC configuration.
If you configure the no-monitor option on a service, you cannot configure load balancing in the Direct Server Return (DSR) mode. For an existing service, if you set the no-monitor option, you cannot configure the DSR mode for the service.

To set the no-monitor option for a new service by using the CLI

At the command prompt, type the following commands to create a service with the health monitor option, and verify the configuration:

add service <serviceName> <IP | serverName> <serviceType> <port> -healthMonitor (YES|NO)
<!--NeedCopy-->

Example:

add service nomonsrvc 10.102.21.21 http 80 -healthMonitor no
Done

show service nomonsrvc
nomonsrvc (10.102.21.21:80) - HTTP
State: UP
Last state change was at Mon Nov 15 22:41:29 2010
Time since last state change: 0 days, 00:00:00.970
Server Name: 10.102.21.21
 Server ID : 0 Monitor Threshold : 0
...
Access Down Service: NO
...
Down state flush: ENABLED
Health monitoring: OFF

1 bound monitor:
1) Monitor Name: tcp-default
State: UNKNOWN Weight: 1
Probes: 3 Failed [Total: 3 Current: 3]
Last response: Probe skipped - Health monitoring is turned off.
Response Time: N/A
Done
<!--NeedCopy-->

To set the no-monitor option for an existing service by using the CLI

At the command prompt, type the following command to set the health monitor option:

set service <name> -healthMonitor (YES|NO)
<!--NeedCopy-->

Example:

By default, the state of a service and the state of the corresponding monitor are UP.
 >show service LB-SVC1
LB-SVC1 (10.102.29.5:80) - HTTP
State: UP


1) Monitor Name: http-ecv
 State: UP Weight: 1
Probes: 99992 Failed [Total: 0 Current: 0]
Last response: Success - Pattern found in response.
Response Time: 3.76 millisec
Done

When the no-monitor option is set on a service, the state of the monitor changes to UNKNOWN.
set service LB-SVC1 -healthMonitor NO
Done

show service LB-SVC1
LB-SVC1 (10.102.29.5:80) - HTTP
State: UP
Last state change was at Fri Dec 10 10:17:37 2010.
Time since last state change: 5 days, 18:55:48.710
Health monitoring: OFF

1) Monitor Name: http-ecv
   State: UNKNOWN Weight: 1
         Probes: 100028 Failed [Total: 0 Current: 0]
   Last response: Probe skipped - Health monitoring is turned off.
     Response Time: 0.0 millisec
  Done
When the no-monitor option is removed, the earlier state of the monitor is resumed.
> set service LB-SVC1 -healthMonitor YES
Done
>show service LB-SVC1
LB-SVC1 (10.102.29.5:80) - HTTP
State: UP
Last state change was at Fri Dec 10 10:17:37 2010
Time since last state change: 5 days, 18:57:47.880
1) Monitor Name: http-ecv
   State: UP Weight: 1
   Probes: 100029 Failed [Total: 0 Current: 0]
   Last response: Success - Pattern found in response.
   Response Time: 5.690 millisec
   Done
<!--NeedCopy-->

To set the no-monitor option for a service by using the GUI

Navigate to Traffic Management > Load Balancing > Services.
Open the service, and clear Health Monitoring.

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

The no-monitor option for services

August 20, 2024

Contributed by:

C C S

August 20, 2024

Contributed by:

C C S

The no-monitor option for services

To set the no-monitor option for a new service by using the CLI

To set the no-monitor option for an existing service by using the CLI

To set the no-monitor option for a service by using the GUI

In this article