ADC

Extra management CPU

August 20, 2024

Contributed by:

C C

If you need better performance for configuration and monitoring of a Citrix ADC MPX appliance, you can allocate an extra management CPU from the appliance’s packet engine pool. This feature is supported on certain Citrix ADC MPX models and all VPX models except the VPX instances that run on Citrix ADC SDX appliances. It affects the output of the stat system cpu and stat system commands.

Supported Citrix ADC MPX models:

25xxx
22xxx
14xxx
115xx
15xxx
26xxx

Note

For Citrix ADC MPX 26xxx models with more than 20 cores, the mandatory extra management CPU feature is enabled by default. For Citrix ADC VPX models, a license that supports atleast 12 vCPUs is required to enable this feature.

Allocate or deallocate an extra management CPU by using the Citrix ADC CLI

At the command prompt, type one of the following commands:

enable extramgmtcpu
disable extramgmtcpu

Note

After you enable and disable this feature, the Citrix ADC appliance displays a warning to restart the appliance, for the changes to take effect.

To show the configured and effective state of an extra management CPU.

At the command prompt, type:

`show extramgmtcpu`

Example

```

> show extramgmtcpu

ConfiguredState:  ENABLED EffectiveState:  ENABLED
<!--NeedCopy--> ```

Note

In this example, the show command is entered before restarting the appliance.

Parameter descriptions of commands listed in the command line interface

enable extramgmtcpu

Enables and dedicates extra CPU for management from PE pool.

Allocate an extra management CPU by using the GUI

To allocate an extra management CPU by using the GUI, navigate to System > Settings and click Configure Extra Management CPU. From the Configured State drop-down menu, select Enabled and then select OK.

To check CPU usage, go to System > Settings > Dashboard.

Configure an extra management CPU by using the NITRO API

Use the following NITRO methods and formats to enable, disable, and show an extra management CPU.

To enable an extra management CPU:

HTTP Method: POST

URL: http://<NSIP>/nitro/v1/config/systemextramgmtcpu?action=enable

Payload: {"systemextramgmtcpu":{}}

```
curl -v -X POST -H "Content-Type: application/json" -u nsroot:nsroot http://10.102.201.92/nitro/v1/config/systemextramgmtcpu?action=enable -d '{"systemextramgmtcpu":{}}'
<!--NeedCopy--> ```

To disable an extra management CPU

HTTP Method: POST

URL: http://<NSIP>/nitro/v1/config/systemextramgmtcpu?action=disable

```
Payload: {"systemextramgmtcpu":{}}

    curl -v -X POST -H "Content-Type: application/json" -u nsroot:nsroot http://10.102.201.92/nitro/v1/config/systemextramgmtcpu?action=disable -d '{"systemextramgmtcpu":{}}'
<!--NeedCopy--> ```

To show an extra management CPU

HTTP Method: GET

URL: http://<NSIP>/nitro/v1/config/systemextramgmtcpu

Example

```
curl -v -X GET -H "Content-Type: application/json" -u nsroot:nsroot http://10.102.201.92/nitro/v1/config/systemextramgmtcpu
<!--NeedCopy--> ```

Statistics and monitoring

The following examples show the differences in the output of the stat system cpu and stat system commands before and after adding an extra management CPU.

stat system cpu

This command displays statistics of CPUs.

Here is a sample output before adding an extra management CPU on one of the supported models.

Example output

```
> stat system cpu

CPU statistics

ID         Usage

8              1

7              1

11             2

1              1

6              1

9              1

3              1

5              1

4              1

10             1

2              1
<!--NeedCopy--> ```

Here is the output after adding an extra management CPU on the same MPX appliance.

```
> stat system cpu

CPU statistics

ID         Usage

9              1

7              1

5              1

8              1

11             2

10             1

6              1

4              1

3              1

2              1
<!--NeedCopy--> ```

2. stat system

This command displays CPU use. In the following example, the output before adding an extra management CPU on one of the supported models is:

Mgmt Additional-CPU usage (%) 0.00

Example output

```
> stat system

Citrix ADC Executive View

System Information:

Up since        Wed Oct 11 11:17:54 2017

/flash Used (%)                        0

Packet CPU usage (%)                1.30

Management CPU usage (%)            4.00

Mgmt CPU0 usage (%)                 4.00

Mgmt Additional-CPU  usage (%)      0.00

Memory usage (MB)                   2167

InUse Memory (%)                    5.76

/var Used (%)                          0
<!--NeedCopy--> ```

In the following example, the output after adding an extra management CPU on the same MPX appliance is:

Mgmt Additional-CPU usage (%) 0.80

```
> stat system

Citrix ADC Executive View

System Information:

Up since        Wed Oct 11 11:55:56 2017

/flash Used (%)                        0

Packet CPU usage (%)                1.20

Management CPU usage (%)            5.70

Mgmt CPU0 usage (%)                10.60

Mgmt Additional-CPU  usage (%)      0.80

Memory usage (MB)                   1970

InUse Memory (%)                    5.75

/var Used (%)                          0

<!--NeedCopy--> ```

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

Extra management CPU

August 20, 2024

Contributed by:

C C

August 20, 2024

Contributed by:

C C

Extra management CPU

Allocate or deallocate an extra management CPU by using the Citrix ADC CLI

Parameter descriptions of commands listed in the command line interface

Allocate an extra management CPU by using the GUI

Configure an extra management CPU by using the NITRO API

Statistics and monitoring

In this article