Citrix SD-WAN Platforms

Citrix SD-WAN WANOP 800

August 22, 2022

Contributed by:

H C

The Citrix SD-WAN WANOP 800 platform has a dual-core processor and 8 GB of memory. The platform has a bandwidth of up to 6 Mbps and up to 10 Mbps, respectively.

The following figure shows the front panel of an SD-WAN WANOP 800 appliance.

Figure 1. Citrix SD-WAN 800, front panel

localized image

The front panel of the SD-WAN 800 appliance has a power button and five LEDs.
The power button switches main power (the power to the power supply) on or off.
The reset button restarts the appliance.

The LEDs provide critical information about different parts of the appliance.

Power Fail—Indicates that a power supply unit has failed.
Information LED—Indicates the following:

Status	Description
Continuously on and red	The appliance is overheated. (This might be a result of cable congestion.)
Blinking red (1 Hz)	Fan failure.
Blinking red (0.25 Hz)	Power failure.
Solid blue	Local UID has been activated. Use this function to locate the server in a rack mount environment.
Blinking blue (300 m/s)	Remote UID is on. Use this function to identify the server from a remote location.

NIC1 and NIC2—Indicate network activity on the LAN1 and WAN1 ports.
HDD—Indicates the status of the hard disk drive.
Power—When blinking, indicates that the power supply unit is receiving power and operating normally.

The following figure shows the back panel of an SD-WAN 800 appliance.

Figure 2. Citrix SD-WAN 800 appliance, back panel

localized image

The following components are visible on the back panel of an SD-WAN 800 appliance:

Cooling fan
Single power supply, rated at 200 watts, 110–240 volts
Accelerated pairs of Ethernet ports (apA and apB) which function as accelerated bridges. Individual port assignments: LAN1 is apA.1, WAN1 is apA.2, LAN2 is apB.1, LAN2 is apB.2.
RS-232 serial console port
One Aux Ethernet port and one management port
Two USB ports
One Solid State Drive (SSD)
- SD-WAN 800 - 240 GB SSD

For initial configuration of a SD-WAN appliance, perform the following tasks::

Configure the appliance for use on your site.
Install the Citrix license.
Enable acceleration.
Enable traffic shaping (inline mode only).

You can configure the appliance by connecting the appliance to your computer through either the Ethernet port or the serial console. The following procedure enables you to configure the appliance by connecting it to your computer through the Ethernet port.

If you want to configure the appliance by connecting it to the computer through the serial console, assign the management service IP address from your set up appliance by completing the Assigning a Management IP Address through the Serial Console procedure.

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

Was this helpful

Citrix SD-WAN WANOP 800

August 22, 2022

Contributed by:

H C

August 22, 2022

Contributed by:

H C

Citrix SD-WAN WANOP 800

In this article