Product Documentation
ADC
14.1 - Current Release 13.1 13.0 12.1
View PDF

SNMP support for admin partitions

September 14, 2021
Contributed by: 
S C

A partitioned Citrix ADC appliance uses the SNMP infrastructure for partition rate limiting and for monitoring partition resource utilization details.

SNMP traps for admin partition rate limiting

On a partitioned Citrix ADC appliance, a PARTITION-RATE-LIMIT alarm can generate nine SNMP traps for notifying a partition resource (such as bandwidth, connection, or memory) has reached its limit or returned to normal.

The following nine SNMP traps are generated when:

  • partitionCONNThresholdReached. The number of active connections for a partition exceeds its high threshold percentage.
  • partitionCONNThresholdNormal. The number of active connections is less than or equal to the normal threshold percentage.
  • partitionBWThresholdReached. The partition’s bandwidth usage reaches its high threshold percentage.
  • partitionMEMThresholdReached. The current memory usage of the partition exceeds its high threshold percentage.
  • partitionMEMThresholdNormal. The current memory usage of the partition becomes less than or equal to the normal threshold percentage.
  • partitionMEMLimitExceeded. The current memory usage of the partition exceeds its memory limit percentage.
  • partitionCONNLimitExceeded. The number of active connections for a partition exceeds its configured limit and new connections are being dropped.
  • partitionCONNLimitNormal. The number of active connections for a partition goes below its configured limit and the partition can now accept a new connection.
  • partitionBWLimitExceeded. The current bandwidth usage for a partition has exceeded its configured limit.

The threshold values for the SNMP traps are non-configurable and are the following:

  • High threshold = 80% (applicable for all partition rate limit traps)
  • Low threshold = 60% (applicable for all partition rate limit traps)
  • Memory limit = 95% (applicable only for partition memory traps)

Configuring PARTITION-RATE-LIMIT alarm

To configure the PARTITION-RATE-LIMIT alarm in a specific partition and enable generation of the SNMP trap messages.

  1. Enable PARTITION-RATE-LIMIT Alarm
  2. Configure PARTITION-RATE-LIMIT Alarm
  3. Configure SNMP Trap Destination

To enable PARTITION-RATE-LIMIT alarm by using the CLI

At the command prompt, type the following commands:

enable snmp alarm PARTITION-RATE-LIMIT

show snmp alarm PARTITION-RATE-LIMIT

To configure PARTITION-RATE-LIMIT Alarm by using the CLI

At the command prompt, type the following command:

set snmp alarm PARTITION-RATE-LIMIT \[-state \( ENABLED | DISABLED )] \[-severity <severity>] \[-logging \( ENABLED | DISABLED )]

To configure the SNMP trap destination by using the CLI

At the command prompt, type the following command:

add snmp trap <trapClass> <trapDestination> \[-version <version>] \[-td <positive\_integer>] \[-destPort <port>] \[-communityName <string>] \[-srcIP <ip\_addr|ipv6\_addr>] \[-severity <severity>] \[-allPartitions \( ENABLED | DISABLED )]

To configure the PARTITION-Rate-Limit alarm by using the GUI

Navigate to System > SNMP > Alarms, select PARTITION-RATE-LIMIT alarm, and configure the alarm parameters.

To configure the SNMP trap destination by using the GUI

Navigate to System > SNMP > Trap, specify the IP address of the destination device.

SNMP monitoring for partition resource utilization

Using SNMP, you can monitor a partition’s resource (such as bandwidth, connection, and memory) utilization details at real time on a Citrix ADC appliance. It is done by sending an SNMP request (such as SNMP GET, SNMP GET BULK, SNMP GETNEXT, or SNMP WALK) from the SNMP Manager.

Note

To monitor partition resources, you must configure the SNMP community in the default partition. Wherein, the partitionTable is maintained in the default partition, and the SNMP communication is done through the NSIP address of the appliance.

Consider a scenario where a Citrix ADC administrator wants to know the bandwidth usage of partition P1 on the appliance. The SNMP Manager retrieves this information by sending an SNMP GET request on the corresponding OID (partitionCurrentBandwidth) to the NSIP address of the appliance. The SNMP agent on the default partition retrieves and sends the current bandwidth usage of P1 to the SNMP Manager through the NSIP address.

The following table lists the SNMP counters which are part of partitionTable and its description:

SNMP Parameter SNMP OID Description
partitionName 1.3.6.1.4.1.5951.4.1.1.88.1.1 Partition name
partitionCurrentBandwidth 1.3.6.1.4.1.5951.4.1.1.88.1.2 Current bandwidth usage of the partition.
partitionCurrentConnections 1.3.6.1.4.1.5951.4.1.1.88.1.3 Current number of active connections of the partition.
partitionMemoryUsagePcnt 1.3.6.1.4.1.5951.4.1.1.88.1.4 Current Memory usage (in percentage) of the partition.
SNMP support for admin partitions
September 14, 2021
Contributed by: 
S C
September 14, 2021
Contributed by: 
S C

In this article

Site feedback | Your privacy choices footer linkYour Privacy Choices | Privacy and legal terms | Cookie preferences | Consent settings | docs.cloud.com
© 1999- Cloud Software Group, Inc. All rights reserved.