ADC

Configure a GSLB service

September 14, 2021

Contributed by:

S C

A GSLB service is a representation of a load balancing or content switching virtual server. A local GSLB service represents a local load balancing or content switching virtual server. A remote GSLB service represents a load balancing or content switching virtual server configured at one of the other sites in the GSLB setup. At each site in the GSLB setup, you can create one local GSLB service and any number of remote GSLB services.

Important

If the load balancing virtual server is either in a GSLB node itself or is in a child node (in parent-child deployment) and no monitors are bound to the GSLB service, then make sure the following:

The GLSB service IP address, port number, and protocol match the virtual server that the service is representing. Else, the service state is marked as DOWN.

To create a GSLB service by using the command line interface

At the command prompt, type the following commands to create a GSLB service and verify the configuration:

add gslb service <serviceName> <serverName | IP> <serviceType> <port>-siteName <string>
show gslb service <serviceName>
<!--NeedCopy-->

Example:

add gslb service Service-GSLB-1 10.14.39.14 HTTP 80 –siteName Site-GSLB-East-Coast
show gslb service Service-GSLB-1
<!--NeedCopy-->

To modify or remove a GSLB service by using the command line interface

To modify a GSLB service, use the set gslb service <serviceName> command. For this command, specify the name of the GSLB service whose configuration you want to modify. You can change the existing values of the parameters either specified by you or set by default. You can change the value of more than one parameter in the same command. Refer to the add gslb service command for details about the parameters. Example
```
 > set gslb service SKP_GSLB_NOTCNAME_SVC2 -maxBandWidth 25 -maxClient 8
 Done
 > sh gslb service SKP_GSLB_NOTCNAME_SVC2
 SKP_GSLB_NOTCNAME_SVC2 (21.211.21.21: 80)- HTTP
 ...
 Max Conn: 8  Max Bandwidth: 25 kbits
 
```

To reset a parameter to its default value, you can use the unset gslb service <serviceName> command and the parameters to be unset. Example

 > unset gslb service SKP_GSLB_NOTCNAME_SVC2 maxBandWidth
 Done
 > sh gslb service SKP_GSLB_NOTCNAME_SVC2
 SKP_GSLB_NOTCNAME_SVC2 (21.211.21.21: 80)- HTTP
 ...
 Max Conn: 8  Max Bandwidth: 0 kbits
 <!--NeedCopy-->

To remove a GSLB service, use the rm gslb service <serviceName> command.

To create a GSLB service by using the configuration utility

Navigate to Traffic Management > GSLB > Services.
Add a new GSLB service, or select an existing service and edit its settings.

To view the statistics of a GSLB service by using the command line interface

At the command prompt, type:

stat gslb service <serviceName>
<!--NeedCopy-->

Example:

stat gslb service Service-GSLB-1
<!--NeedCopy-->

To view the statistics of a GSLB service by using the configuration utility

Navigate to Traffic Management > GSLB > Services.
Select the GSLB Service and click Statistics.

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

Configure a GSLB service

September 14, 2021

Contributed by:

S C

September 14, 2021

Contributed by:

S C

Configure a GSLB service

To create a GSLB service by using the command line interface

To modify or remove a GSLB service by using the command line interface

To create a GSLB service by using the configuration utility

To view the statistics of a GSLB service by using the command line interface

To view the statistics of a GSLB service by using the configuration utility

In this article